VMware에서 삼바설치

[polaris]

삼바설치로 인해 몇일간 밤을 새다가 결국엔 이렇게 SOS를 보냅니다.
리눅스 초보인 제가 VMware를 만나서 너무 신기해 이것 저것 해보는데
삼바는 저를 힘들게 하는군요

저의 컴퓨터 환경은
호스트 : 윈도우 2000 프로
게스트 : VMware3.2버전에 레드햇리눅스 7.2 설치
인터넷 환경은
공유기를 쓰고 있습니다.(하나로통신)
네트워크 정보는 모두 자동으로 IP주소 받기로 했으며
도스창에서 ipconfig 으로 다음과 같은 정보가 나옵니다.

로컬영역연결에 등록정보는
IP : 192.168.0.5 Subnet Mask : 255.255.255.0
Default Gateway/DHCP Servver : 192.168.0.1
DNS server : 210.220.163.82 / 210.94.6.67

VMware를 설치하니까 2개의 네트워크 카드가 잡히는 군요

VMware Virtual Ethernet Adapter (basic host-only support for VMnet1)의 등록정보
IP : 192.168.152.1 / Subnet Mask : 255.255.255.0
DHCP Server : 192.168.152.254

VMware Virtual Ethernet Adapter (Network Address Translation (NAT) for VMnet8)
IP : 192.168.20.1 / Subnet Mask : 255.255.255.0
DHCP Server : 192.168.20.254
Primary WINS Server : 192.168.20.2

이상이 윈도우 2000에서의 네트워크 정보이고

다음은 VMware는 NAT로 설치를 했습니다.
설치시 Bridged , NAT , Host-only , Custom 등이 있는데 정확히 어떤건지는 모르고 일단 NAT으로 설치를 해서
인터넷까지 됩니다. 아파치도 돌려보고 SSH 랑 FTP서버도 돌려지는데 유독 삼바서버가 안되네요...(항상 골칫거리였습니다.)
즉,,,호스트랑 ( 윈도우2000 ) 네트워크 환경에서 리눅스 컴이 보이지를 않습니다.

리눅스에서 route 정보
Destination Gateway Genmask Flags Metric Ref Use IFace
192.168.20.0 * 255.255.255.0 U 0 0 0 eth0
127.0.0.0 * 255.0.0.0 U 0 0 0 lo
default 192.168.20.2 0.0.0.0 UG 0 0 0 eth0

ifconfig 정보
eth Link encap:Ethernet .........................
inet addr : 192.168.20.130 Bcast : 192.168.20.255 Mask : 255.255.255.0
................................
lo Link encap : Local Loopback
inet addr : 127.0.0.1 Mask : 255.0.0.0
............................

ps -aux | grep smb 정보
root 3502 0.0 0.6 3384 1304 ? S 15:32 0:00 smbd -D
root 5394 0.0 0.3 2524 672 tty1 S 22:54 0:00 grep smb

/etc/sysconf/network 정보
NETWORKING=yes
HOSTNAME=localhost.localdomain

/etc/sysconfig/network-scripts/ifcfg-eth0 정보
DEVICE=eth0
BOOTPROTO=dhcp
ONBOOT=yes

/etc/hosts 정보
127.0.0.1 localhost.localdomain localhost

/etc/host.conf정보
order hosts, bind

/etc/resolv.conf정보
domain localdomain
nameserver 192.168.20.2
search localdomain

/home디렉토리에 삼바로 공유시킬 samba라는 폴더 만들어주고요...
samba폴더 권한을 chmod 777로 주었고
윈도우 계정도 있어야된다는소릴 어디서 들어서
리눅스에서 administrator라는 계정도 useradd로 만들어 주었구요

윈도우에서 ping을 리눅스 ip인 192.168.20.130 로 보냈더니 잘 보내지구요
리눅스에서 ping을 윈도우 ip인 192.168.0.5 로 보냈더니 잘 보내지구요..
아래에 smb.conf파일 정보 있구요...
제 생각엔 삼바문제는 아닌거 같은데...
삼바는 같은 네트워크 주소에서만 되는거 아닌가요....
그래서 192.168.0 번대랑 192.168.20번대랑 틀려서 그런거 아닌가요?
어디사이트게시판에 보니 별다른 설정 없이 잘된다고 하는데 저는 왜 그런지 모르겠어요..ㅠ.ㅠ

제발 저의 밤샘을 그만 시켜주세요....

게스트 smb.conf 설정정보

# This is the main Samba configuration file. You should read the
# smb.conf(5) manual page in order to understand the options listed
# here. Samba has a huge number of configurable options (perhaps too
# many!) most of which are not shown in this example
#
# Any line which starts with a ; (semi-colon) or a # (hash)
# is a comment and is ignored. In this example we will use a #
# for commentry and a ; for parts of the config file that you
# may wish to enable
#
# NOTE: Whenever you modify this file you should run the command "testparm"
# to check that you have not made any basic syntactic errors.
#
#======================= Global Settings =====================================
[global]

# workgroup = NT-Domain-Name or Workgroup-Name
workgroup = HOME

# server string is the equivalent of the NT Description field
server string = Samba Server

# This option is important for security. It allows you to restrict
# connections to machines which are on your local network. The
# following example restricts access to two C class networks and
# the "loopback" interface. For more examples of the syntax see
# the smb.conf man page
; hosts allow = 192.168.1. 192.168.2. 127.

# if you want to automatically load your printer list rather
# than setting them up individually then you'll need this
printcap name = /etc/printcap
load printers = yes

# It should not be necessary to spell out the print system type unless
# yours is non-standard. Currently supported print systems include:
# bsd, sysv, plp, lprng, aix, hpux, qnx
printing = lprng

# Uncomment this if you want a guest account, you must add this to /etc/passwd
# otherwise the user "nobody" is used
; guest account = pcguest

# this tells Samba to use a separate log file for each machine
# that connects
log file = /var/log/samba/%m.log

# Put a capping on the size of the log files (in Kb).
max log size = 50

# Security mode. Most people will want user level security. See
# security_level.txt for details.
security = share

# Use password server option only with security = server
# The argument list may include:
# password server = My_PDC_Name [My_BDC_Name] [My_Next_BDC_Name]
# or to auto-locate the domain controller/s
# password server = *
; password server = <NT-Server-Name>

# Password Level allows matching of _n_ characters of the password for
# all combinations of upper and lower case.
; password level = 8
; username level = 8

# You may wish to use password encryption. Please read
# ENCRYPTION.txt, Win95.txt and WinNT.txt in the Samba documentation.
# Do not enable this option unless you have read those documents
encrypt passwords = yes
smb passwd file = /etc/samba/smbpasswd

# The following is needed to keep smbclient from spouting spurious errors
# when Samba is built with support for SSL.
; ssl CA certFile = /usr/share/ssl/certs/ca-bundle.crt

# The following are needed to allow password changing from Windows to
# update the Linux sytsem password also.
# NOTE: Use these with 'encrypt passwords' and 'smb passwd file' above.
# NOTE2: You do NOT need these to allow workstations to change only
# the encrypted SMB passwords. They allow the Unix password
# to be kept in sync with the SMB password.
; unix password sync = Yes
; passwd program = /usr/bin/passwd %u
; passwd chat = *New*password* %n\n *Retype*new*password* %n\n *passwd:*all*authentication*tokens*updated*successfully*

# Unix users can map to different SMB User names
; username map = /etc/samba/smbusers

# Using the following line enables you to customise your configuration
# on a per machine basis. The %m gets replaced with the netbios name
# of the machine that is connecting
; include = /etc/samba/smb.conf.%m

# This parameter will control whether or not Samba should obey PAM's
# account and session management directives. The default behavior is
# to use PAM for clear text authentication only and to ignore any
# account or session management. Note that Samba always ignores PAM
# for authentication in the case of encrypt passwords = yes

; obey pam restrictions = yes

# Most people will find that this option gives better performance.
# See speed.txt and the manual pages for details
socket options = TCP_NODELAY SO_RCVBUF=8192 SO_SNDBUF=8192

# Configure Samba to use multiple interfaces
# If you have multiple network interfaces then you must list them
# here. See the man page for details.
; interfaces = 192.168.12.2/24 192.168.13.2/24

# Configure remote browse list synchronisation here
# request announcement to, or browse list sync from:
# a specific host or from / to a whole subnet (see below)
; remote browse sync = 192.168.3.25 192.168.5.255
# Cause this host to announce itself to local subnets here
; remote announce = 192.168.1.255 192.168.2.44

# Browser Control Options:
# set local master to no if you don't want Samba to become a master
# browser on your network. Otherwise the normal election rules apply
; local master = no

# OS Level determines the precedence of this server in master browser
# elections. The default value should be reasonable
; os level = 33

# Domain Master specifies Samba to be the Domain Master Browser. This
# allows Samba to collate browse lists between subnets. Don't use this
# if you already have a Windows NT domain controller doing this job
; domain master = yes

# Preferred Master causes Samba to force a local browser election on startup
# and gives it a slightly higher chance of winning the election
; preferred master = yes

# Enable this if you want Samba to be a domain logon server for
# Windows95 workstations.
; domain logons = yes

# if you enable domain logons then you may want a per-machine or
# per user logon script
# run a specific logon batch file per workstation (machine)
; logon script = %m.bat
# run a specific logon batch file per username
; logon script = %U.bat

# Where to store roving profiles (only for Win95 and WinNT)
# %L substitutes for this servers netbios name, %U is username
# You must uncomment the [Profiles] share below
; logon path = \\%L\Profiles\%U

# Windows Internet Name Serving Support Section:
# WINS Support - Tells the NMBD component of Samba to enable it's WINS Server
; wins support = yes

# WINS Server - Tells the NMBD components of Samba to be a WINS Client
# Note: Samba can be either a WINS Server, or a WINS Client, but NOT both
; wins server = w.x.y.z

# WINS Proxy - Tells Samba to answer name resolution queries on
# behalf of a non WINS capable client, for this to work there must be
# at least one WINS Server on the network. The default is NO.
; wins proxy = yes

# DNS Proxy - tells Samba whether or not to try to resolve NetBIOS names
# via DNS nslookups. The built-in default for versions 1.9.17 is yes,
# this has been changed in version 1.9.18 to no.
dns proxy = no

# Case Preservation can be handy - system default is _no_
# NOTE: These can be set on a per share basis
; preserve case = no
; short preserve case = no
# Default case is normally upper case for all DOS files
; default case = lower
# Be very careful with case sensitivity - it can break things!
; case sensitive = no

coding system = euc
client code page = 949

#============================ Share Definitions ==============================
[homes]
comment = Home Directories
browseable = no
writable = yes
valid users = %S
create mode = 0664
directory mode = 0775
# If you want users samba doesn't recognize to be mapped to a guest user
; map to guest = bad user


# Un-comment the following and create the netlogon directory for Domain Logons
; [netlogon]
; comment = Network Logon Service
; path = /usr/local/samba/lib/netlogon
; guest ok = yes
; writable = no
; share modes = no


# Un-comment the following to provide a specific roving profile share
# the default is to use the user's home directory
;[Profiles]
; path = /usr/local/samba/profiles
; browseable = no
; guest ok = yes


# NOTE: If you have a BSD-style print system there is no need to
# specifically define each individual printer
[printers]
comment = All Printers
path = /var/spool/samba
browseable = no
# Set public = yes to allow user 'guest account' to print
guest ok = no
writable = no
printable = yes

# This one is useful for people to share files
;[tmp]
; comment = Temporary file space
; path = /tmp
; read only = no
; public = yes

# A publicly accessible directory, but read only, except for people in
# the "staff" group
[public]
comment = Public Stuff
path = /home/samba
public = yes
writable = yes
printable = no
write list = @staff

# Other examples.
#
# A private printer, usable only by fred. Spool data will be placed in fred's
# home directory. Note that fred must have write access to the spool directory,
# wherever it is.
;[fredsprn]
; comment = Fred's Printer
; valid users = fred
; path = /home/fred
; printer = freds_printer
; public = no
; writable = no
; printable = yes

# A private directory, usable only by fred. Note that fred requires write
# access to the directory.
;[fredsdir]
; comment = Fred's Service
; path = /usr/somewhere/private
; valid users = fred
; public = no
; writable = yes
; printable = no

# a service which has a different directory for each machine that connects
# this allows you to tailor configurations to incoming machines. You could
# also use the %U option to tailor it by user name.
# The %m gets replaced with the machine name that is connecting.
;[pchome]
; comment = PC Directories
; path = /usr/local/pc/%m
; public = no
; writable = yes

# A publicly accessible directory, read/write to all users. Note that all files
# created in the directory by users will be owned by the default user, so
# any user with access can delete any other user's files. Obviously this
# directory must be writable by the default user. Another user could of course
# be specified, in which case all files would be owned by that user instead.
;[public]
; path = /usr/somewhere/else/public
; public = yes
; only guest = yes
; writable = yes
; printable = no

# The following two entries demonstrate how to share a directory so that two
# users can place files there that will be owned by the specific users. In this
# setup, the directory should be writable by both users and should have the
# sticky bit set on it to prevent abuse. Obviously this could be extended to
# as many users as required.
;[myshare]
; comment = Mary's and Fred's stuff
; path = /usr/somewhere/shared
; valid users = mary fred
; public = no
; writable = yes
; printable = no
; create mask = 0765

이상입니다...