# =========================================================== # MegaCli 명령 실행 결과 예 # # 2011.8.8(Mon) # by 좋은진호(truefeel, http://coffeenix.net/ ) # =========================================================== # ./MegaCli -PDList -aAll Adapter #0 Enclosure Device ID: 32 Slot Number: 0 Enclosure position: 0 Device Id: 0 Sequence Number: 2 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SAS Raw Size: 136.732 GB [0x11177328 Sectors] Non Coerced Size: 136.232 GB [0x11077328 Sectors] Coerced Size: 136.125 GB [0x11040000 Sectors] Firmware state: Online, Spun Up SAS Address(0): 0x5000c5003b5aaa1d SAS Address(1): 0x0 Connected Port Number: 0(path0) Inquiry Data: SEAGATE ST9146852SS ___생략___ FDE Capable: Not Capable FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: Unknown Link Speed: Unknown Media Type: Hard Disk Device Drive Temperature :26C (78.80 F) Enclosure Device ID: 32 Slot Number: 1 Enclosure position: 0 Device Id: 1 Sequence Number: 2 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SAS Raw Size: 136.732 GB [0x11177328 Sectors] Non Coerced Size: 136.232 GB [0x11077328 Sectors] Coerced Size: 136.125 GB [0x11040000 Sectors] Firmware state: Online, Spun Up SAS Address(0): 0x5000c5003b5aaad1 SAS Address(1): 0x0 Connected Port Number: 1(path0) Inquiry Data: SEAGATE ST9146852SS ___생략___ FDE Capable: Not Capable FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: Unknown Link Speed: Unknown Media Type: Hard Disk Device Drive Temperature :26C (78.80 F) Enclosure Device ID: 32 Slot Number: 2 Enclosure position: 0 Device Id: 2 Sequence Number: 2 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SAS Raw Size: 136.732 GB [0x11177328 Sectors] Non Coerced Size: 136.232 GB [0x11077328 Sectors] Coerced Size: 136.125 GB [0x11040000 Sectors] Firmware state: Online, Spun Up SAS Address(0): 0x5000c5002be1a081 SAS Address(1): 0x0 Connected Port Number: 2(path0) Inquiry Data: SEAGATE ST9146852SS ___생략___ FDE Capable: Not Capable FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: Unknown Link Speed: Unknown Media Type: Hard Disk Device Drive Temperature :25C (77.00 F) Enclosure Device ID: 32 Slot Number: 3 Enclosure position: 0 Device Id: 3 Sequence Number: 2 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SAS Raw Size: 136.732 GB [0x11177328 Sectors] Non Coerced Size: 136.232 GB [0x11077328 Sectors] Coerced Size: 136.125 GB [0x11040000 Sectors] Firmware state: Online, Spun Up SAS Address(0): 0x5000c5002be44341 SAS Address(1): 0x0 Connected Port Number: 3(path0) Inquiry Data: SEAGATE ST9146852SS ___생략___ FDE Capable: Not Capable FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: Unknown Link Speed: Unknown Media Type: Hard Disk Device Drive Temperature :25C (77.00 F) Exit Code: 0x00 # ./MegaCli -LDInfo -LALL -aAll Adapter 0 -- Virtual Drive Information: Virtual Drive: 0 (Target Id: 0) Name : RAID Level : Primary-5, Secondary-0, RAID Level Qualifier-3 Size : 408.375 GB State : Optimal Strip Size : 64 KB Number Of Drives : 4 Span Depth : 1 Default Cache Policy: WriteBack, ReadAheadNone, Direct, No Write Cache if Bad BBU Current Cache Policy: WriteBack, ReadAheadNone, Direct, No Write Cache if Bad BBU Access Policy : Read/Write Disk Cache Policy : Disk's Default Encryption Type : None Exit Code: 0x00 # ./MegaCli -EncInfo -aALL Number of enclosures on adapter 0 -- 1 Enclosure 0: Device ID : 32 Number of Slots : 6 Number of Power Supplies : 0 Number of Fans : 0 Number of Temperature Sensors : 0 Number of Alarms : 0 Number of SIM Modules : 0 Number of Physical Drives : 4 Status : Normal Position : 0 Connector Name : Unavailable Connected in Multipath : No Inquiry data : Vendor Identification : DP Product Identification : BACKPLANE Product Revision Level : 1.07 Vendor Specific : ___생략___ Exit Code: 0x00 # ./MegaCli -AdpAllInfo -aALL Adapter #0 ============================================================================== Versions ================ Product Name : PERC 6/i Integrated Serial No : 1122334455667788 FW Package Build: 6.3.0-0001 Mfg. Data ================ Mfg. Date : 06/24/08 Rework Date : 06/24/08 Revision No : Battery FRU : N/A Image Versions in Flash: ================ FW Version : 1.22.12-0952 BIOS Version : 2.04.00 WebBIOS Version : 1.1-46-e_15-Rel Ctrl-R Version : 1.02-015B Preboot CLI Version: 01.00-023:#%00006 Boot Block Version : 1.00.00.01-0011 Pending Images in Flash ================ None PCI Info ================ Vendor Id : 1000 Device Id : 0060 SubVendorId : 1028 SubDeviceId : 1f0c Host Interface : PCIE Number of Frontend Port: 0 Device Interface : PCIE Number of Backend Port: 8 Port : Address 0 5000c5003b5aaa1d 1 5000c5003b5aaad1 2 5000c5002be1a081 3 5000c5002be44341 4 0000000000000000 5 0000000000000000 6 0000000000000000 7 0000000000000000 HW Configuration ================ SAS Address : 5782bcb038c63500 BBU : Present Alarm : Absent NVRAM : Present Serial Debugger : Present Memory : Present Flash : Present Memory Size : 256MB TPM : Absent On board Expander: Absent Upgrade Key : Absent Temperature sensor for ROC : Absent Temperature sensor for controller : Absent Settings ================ Current Time : 2:41:25 8/8, 2011 Predictive Fail Poll Interval : 300sec Interrupt Throttle Active Count : 16 Interrupt Throttle Completion : 50us Rebuild Rate : 30% PR Rate : 30% BGI Rate : 30% Check Consistency Rate : 30% Reconstruction Rate : 30% Cache Flush Interval : 4s Max Drives to Spinup at One Time : 2 Delay Among Spinup Groups : 12s Physical Drive Coercion Mode : 128MB Cluster Mode : Disabled Alarm : Disabled Auto Rebuild : Enabled Battery Warning : Enabled Ecc Bucket Size : 15 Ecc Bucket Leak Rate : 1440 Minutes Restore HotSpare on Insertion : Disabled Expose Enclosure Devices : Disabled Maintain PD Fail History : Disabled Host Request Reordering : Enabled Auto Detect BackPlane Enabled : SGPIO/i2c SEP Load Balance Mode : Auto Use FDE Only : No Security Key Assigned : No Security Key Failed : No Security Key Not Backedup : No Default LD PowerSave Policy : Controller Defined Maximum number of direct attached drives to spin up in 1 min : 0 Any Offline VD Cache Preserved : No Allow Boot with Preserved Cache : No Disable Online Controller Reset : No PFK in NVRAM : No Use disk activity for locate : No Capabilities ================ RAID Level Supported : RAID0, RAID1, RAID5, RAID6, RAID00, RAID10, RAID50, RAID60, PRL 11, PRL 11 with spanning, SRL 3 supported, PRL11-RLQ0 DDF layout with no span, PRL11-RLQ0 DDF layout with span Supported Drives : SAS, SATA Allowed Mixing: Mix in Enclosure Allowed Status ================ ECC Bucket Count : 0 Limitations ================ Max Arms Per VD : 32 Max Spans Per VD : 8 Max Arrays : 128 Max Number of VDs : 64 Max Parallel Commands : 1008 Max SGE Count : 80 Max Data Transfer Size : 8192 sectors Max Strips PerIO : 42 Min Strip Size : 8 KB Max Strip Size : 1.0 MB Max Configurable CacheCade Size: 0 GB Current Size of CacheCade : 0 GB Current Size of FW Cache : 0 MB Device Present ================ Virtual Drives : 1 Degraded : 0 Offline : 0 Physical Devices : 5 Disks : 4 Critical Disks : 0 Failed Disks : 0 Supported Adapter Operations ================ Rebuild Rate : Yes CC Rate : Yes BGI Rate : Yes Reconstruct Rate : Yes Patrol Read Rate : Yes Alarm Control : Yes Cluster Support : No BBU : Yes Spanning : Yes Dedicated Hot Spare : Yes Revertible Hot Spares : Yes Foreign Config Import : Yes Self Diagnostic : Yes Allow Mixed Redundancy on Array : No Global Hot Spares : Yes Deny SCSI Passthrough : No Deny SMP Passthrough : No Deny STP Passthrough : No Support Security : No Snapshot Enabled : No Support the OCE without adding drives : No Support PFK : No Supported VD Operations ================ Read Policy : Yes Write Policy : Yes IO Policy : Yes Access Policy : Yes Disk Cache Policy : Yes Reconstruction : Yes Deny Locate : No Deny CC : No Allow Ctrl Encryption: No Enable LDBBM : No Support Breakmirror : No Power Savings : No Supported PD Operations ================ Force Online : Yes Force Offline : Yes Force Rebuild : Yes Deny Force Failed : No Deny Force Good/Bad : No Deny Missing Replace : No Deny Clear : No Deny Locate : No Support Temperature : No Disable Copyback : No Enable JBOD : No Enable Copyback on SMART : No Enable Copyback to SSD on SMART Error : No Enable SSD Patrol Read : No PR Correct Unconfigured Areas : Yes Error Counters ================ Memory Correctable Errors : 0 Memory Uncorrectable Errors : 0 Cluster Information ================ Cluster Permitted : No Cluster Active : No Default Settings ================ Phy Polarity : 0 Phy PolaritySplit : 0 Background Rate : 30 Strip Size : 64kB Flush Time : 4 seconds Write Policy : WB Read Policy : None Cache When BBU Bad : Disabled Cached IO : No SMART Mode : Mode 6 Alarm Disable : No Coercion Mode : 128MB ZCR Config : Unknown Dirty LED Shows Drive Activity : No BIOS Continue on Error : No Spin Down Mode : None Allowed Device Type : SAS/SATA Mix Allow Mix in Enclosure : Yes Allow HDD SAS/SATA Mix in VD : No Allow SSD SAS/SATA Mix in VD : No Allow HDD/SSD Mix in VD : No Allow SATA in Cluster : No Max Chained Enclosures : 1 Disable Ctrl-R : No Enable Web BIOS : No Direct PD Mapping : Yes BIOS Enumerate VDs : Yes Restore Hot Spare on Insertion : No Expose Enclosure Devices : No Maintain PD Fail History : No Disable Puncturing : No Zero Based Enclosure Enumeration : Yes PreBoot CLI Enabled : No LED Show Drive Activity : No Cluster Disable : Yes SAS Disable : No Auto Detect BackPlane Enable : SGPIO/i2c SEP Use FDE Only : No Enable Led Header : No Delay during POST : 0 EnableCrashDump : No Disable Online Controller Reset : No EnableLDBBM : No Un-Certified Hard Disk Drives : Block Treat Single span R1E as R10 : No Max LD per array : 16 Power Saving option : All power saving options are enabled Default spin down time in minutes: 0 Enable JBOD : No Time taken to detect CME : 60s Exit Code: 0x00 # ./MegaCli -ShowSummary -aALL System OS Name (IP Address) : Not Recognized OS Version : Not Recognized Driver Version : Not Recognized CLI Version : 8.01.06 Hardware Controller ProductName : PERC 6/i Integrated(Bus 0, Dev 0) SAS Address : 5782bcb038c63500 FW Package Version: 6.3.0-0001 Status : Optimal BBU BBU Type : BBU Status : Healthy Enclosure Product Id : BACKPLANE Type : SES Status : OK PD Connector : 0: Slot 0 Vendor Id : SEAGATE Product Id : ST9146852SS State : Online Disk Type : SAS,Hard Disk Device Capacity : 136.125 GB Power State : Active Connector : 0: Slot 1 Vendor Id : SEAGATE Product Id : ST9146852SS State : Online Disk Type : SAS,Hard Disk Device Capacity : 136.125 GB Power State : Active Connector : 0: Slot 2 Vendor Id : SEAGATE Product Id : ST9146852SS State : Online Disk Type : SAS,Hard Disk Device Capacity : 136.125 GB Power State : Active Connector : 0: Slot 3 Vendor Id : SEAGATE Product Id : ST9146852SS State : Online Disk Type : SAS,Hard Disk Device Capacity : 136.125 GB Power State : Active Storage Virtual Drives Virtual drive : Target Id 0 ,VD name Size : 408.375 GB State : Optimal RAID Level : 5 Exit Code: 0x00 # ./MegaCli -AdpBbuCmd -aALL BBU status for Adapter: 0 BatteryType: BBU Voltage: 4011 mV Current: 0 mA Temperature: 19 C BBU Firmware Status: Charging Status : None Voltage : OK Temperature : OK Learn Cycle Requested : No Learn Cycle Active : No Learn Cycle Status : OK Learn Cycle Timeout : No I2c Errors Detected : No Battery Pack Missing : No Battery Replacement required : No Remaining Capacity Low : No Periodic Learn Required : No Transparent Learn : No Battery state: GasGuageStatus: Fully Discharged : No Fully Charged : Yes Discharging : Yes Initialized : Yes Remaining Time Alarm : No Remaining Capacity Alarm: No Discharge Terminated : No Over Temperature : No Charging Terminated : Yes Over Charged : No Relative State of Charge: 97 % Charger Status: Complete Remaining Capacity: 1646 mAh Full Charge Capacity: 1700 mAh isSOHGood: Yes BBU Capacity Info for Adapter: 0 Relative State of Charge: 97 % Absolute State of charge: 92 % Remaining Capacity: 1646 mAh Full Charge Capacity: 1700 mAh Run time to empty: Battery is not being discharged Average time to empty: Battery is not being discharged Average Time to full: Battery is not being charged Cycle Count: 2 Max Error = 2 % Remaining Capacity Alarm = 180 mAh Remining Time Alarm = 10 Min BBU Design Info for Adapter: 0 Date of Manufacture: 05/31, 2011 Design Capacity: 1800 mAh Design Voltage: 3700 mV Specification Info: 49 Serial Number: ___생략___ Pack Stat Configuration: 0x0014 Manufacture Name: SMP-SDI2.0 Device Name: DLFR463 Device Chemistry: LION Battery FRU: N/A BBU Properties for Adapter: 0 Auto Learn Period: 7776000 Sec Next Learn time: 371015371 Sec Learn Delay Interval:0 Hours Auto-Learn Mode: Enabled Exit Code: 0x00